How Repair Screen Iphone 6

Introduction

Larn how to replace your iPhone 6 screen. This part comes with the front end-facing camera, earpiece speaker and LCD shield plate already installed, making for an easier repair.

All you need to practice is remove the old screen and transfer the dwelling push to the new screen.

You lot tin also utilize this guide to replace the front end panel assembly cable bracket.

Video Overview

• Before disassembling your iPhone, belch the battery below 25%. A charged lithium-ion bombardment can take hold of fire and/or explode if accidentally punctured.

• Ability off your iPhone earlier showtime disassembly.

• Remove the ii three.six mm-long P2 Pentalobe screws side by side to the Lightning connector.



• If your display drinking glass is cracked, go along further breakage independent and preclude actual impairment during your repair by taping over the glass.

• Lay overlapping strips of clear packing record over the iPhone's display until the whole face is covered.

• This will go on glass shards contained and provide structural integrity when prying and lifting the display.

• Wear safety glasses to protect your eyes from any glass shaken free during the repair.

• If the broken drinking glass makes it difficult to get a suction cup to stick in the side by side few steps, attempt folding a strong slice of tape (such as duct tape) into a handle and lifting the display with that instead.

• The side by side three steps demonstrate using the iSclack, a swell tool for safely opening the iPhone 6 that nosotros recommend for anyone doing more than one repair. If you aren't using the iSclack, skip down iii steps for an alternating method.

• If the plastic depth guess is attached at the center of the iSclack, remove it now—information technology'south not needed for larger phones like the iPhone vi.

• Close the handle on the iSclack, opening the suction-cup jaws.

• Place the bottom of your iPhone in between the suction cups.

• Position the iSclack's upper suction cup against the display, but above (but not covering) the home button.

• Open the handles to shut the jaws of the iSclack. Center the suction cups and press them firmly onto the tiptop and lesser of the iPhone.

• If your display or back glass is badly cracked, covering it with a layer of clear packing tape may help the suction cups adhere. The iSclack also includes two pieces of record for this purpose.

• Hold onto your iPhone deeply and close the handle of the iSclack to separate the suction cups, pulling the front end console up from the rear example.

• The iSclack is designed to safely open your iPhone just enough to carve up the pieces, but not plenty to impairment the display cables.

• Peel the ii suction cups off your iPhone.

• Skip the next 3 steps and continue on to Step viii.

• If you don't take an iSclack, use a single suction cup to lift the front console:

• Press a suction cup onto the screen, just higher up the home button.

• Be sure the cup is pressed securely onto the screen to become a tight seal.

• If your display is badly cracked, covering it with a layer of clear packing tape may let the suction cup to adhere. Alternatively, very strong tape may be used instead of the suction cup. If all else fails, you can superglue the suction loving cup to the cleaved screen.

• While holding the iPhone down with one hand, pull up on the suction loving cup to slightly split up the front console assembly from the rear instance.

• Take your fourth dimension and apply firm, constant force. The display assembly is a much tighter fit than most devices.

• Using a plastic opening tool, brainstorm to gently pry the rear instance downwards, away from the display assembly, while continuing to pull up with the suction cup.

• At that place are several clips belongings the front panel assembly to the rear instance, so you may need to use a combination of the suction loving cup and plastic opening tool to free the forepart panel assembly.

• Pull the plastic nub to release the vacuum seal on the suction loving cup.

• Remove the suction loving cup from the display assembly.

• Open the iPhone by swinging the home button cease of the front panel assembly away from the rear example, using the top of the phone as a hinge.

• Several clips along the acme edge of the front panel form a fractional hinge.

• During reassembly, align the clips just below the top border of the rear example. Then, slide the front console upward until its top border is flush with that of the rear case.

• Open the brandish to nigh a 90º angle, and lean it against something to keep information technology propped upwardly while you're working on the phone.

• In a pinch, an unopened canned drink works well for this.

• Add a safety band to keep the display securely in place while you piece of work. This prevents undue strain on the display cables.

• Remove the following Phillips screws from the battery connector bracket:

• One 2.2 mm screw

• One iii.2 mm spiral

• During your repair, proceed track of each screw and make sure it goes back exactly where information technology came from to avoid damaging your phone.

• Remove the metal bombardment connector bracket from the iPhone.

• Employ a plastic opening tool to gently pry the battery connector upwardly from its socket on the logic lath.

• Take care to only pry upward on the battery connector, and not the socket on the logic board. If you pry up on the logic board socket, you may break the connector entirely.

• Remove the following v Phillips screws securing the front panel assembly cable bracket:

• Three one.2 mm screws

• I 1.7 mm spiral

• I 3.1 mm screw

• Wrong placement of these screws during reassembly will cause permanent damage to your iPhone's logic board.

• Remove the front panel assembly cable bracket from the logic board.

• In the next four steps, take care to pry upward only on the cablevision connectors, and not on their sockets on the logic board.

• Use a spudger or a fingernail to disconnect the front-facing photographic camera and sensor cable connector.

• Apply a spudger or a fingernail to disconnect the home button cable connector.

• Brand sure the battery is asunder before you disconnect or reconnect the cable in this step.

• Use a spudger or a fingernail to disconnect the display data cablevision connector.

• When reassembling your phone, the display data cable may pop off its connector. This can result in white lines or a bare screen when powering your telephone dorsum on. If that happens, only reconnect the cable and power cycle your phone. The best style to power cycle your phone is to disconnect and reconnect the bombardment connector.

• Use the apartment end of a spudger to disconnect the digitizer cable connector.

• When reconnecting the digitizer cablevision, do not printing the center of the connector. Press i finish of the connector, and then printing the contrary cease. Pressing in the heart of the connector tin bend the component and cause digitizer impairment.

• Remove the front panel assembly from the rear instance.

• Remove the two 1.ix mm Phillips screws securing the domicile button bracket.

• Remove the home button bracket from the front console.

• Use the bespeak of a spudger to disconnect the abode button cable connector by pushing information technology up and away from the home button.

• The rubber membrane surrounding the dwelling house button is very sparse and tears easily.

• Apply mild heat (with an iOpener, heat gun, or pilus dryer) to soften the agglutinative securing the home push button membrane.

• Using your fingertip, apply house, abiding force per unit area on the home push from the front side of the display assembly, until the membrane starts to carve up from the front panel.

• Exercise not button the domicile button all the way through—y'all just need to become a corner free so that yous can pry it complimentary with a spudger.

• Peel the domicile button the rest of the way off of the display by prying gently with a spudger.

• Use the indicate of a spudger to advisedly separate the home button cable from the adhesive securing information technology to the front panel.

• If the cable doesn't split up hands, apply heat using an iOpener or hair dryer to soften the agglutinative, and endeavour again. Be careful not to harm the cable.

• Once all the adhesive has been separated, remove the home button from the front end panel.

• If you are replacing a broken front console, there may be glass shards stuck to the home push button. Carefully remove whatever remaining glass earlier transferring your dwelling push button to a new display.

• Your replacement part may come up with an extra Phillips screw already installed left of the Home Button. Remove the unnecessary screw then that yous can reinstall the home push bracket.

Conclusion

To reassemble your device, follow these instructions in contrary club.

Embed this guide

Choose a size and copy the code below to embed this guide as a small widget on your site / forum.

Preview

Source: https://www.ifixit.com/Guide/iPhone+6+Screen+Replacement/29339

Posted by: mannfoomescree.blogspot.com

Share this post